Of course, the paper specs are only half the story, and the real question that’s on everyone’s mind is how the new Phenom II processors will overclock on this motherboard. Thanks for the replies people! I am going to go check my bios settings as i think i see a difference in mine will report back in 5 minutes. Select the RAID type, stripe, mirror, whatever, select the member drives, in your case the WD’s, the stripe size, and then create the array. Gigabyte includes a number of blue LED illuminated system control buttons on the motherboard to make it easy to troubleshoot and set up the system when it’s not attached to a proper chassis.
|Date Added:||22 June 2012|
|File Size:||37.12 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Total System Power Draw and Conclusions. Funtional, RAM Mhz ok. Raid 0 if done right is stable and fast and as realiable as a gaa-ma790fxt-ud5p hard drive.
Corsair T Graphite Owners Club. Discrete videocards are handled by a pair of PCI Express 2. Register Now In order to be able to post messages on the Overclock. After the array is created you’ll boot from the Windows setup CD. Each time i sta, it will be stuck at the dot prompt “AMD data change Case Corsair Carbide R. First off that PSU isnt that good a at peak can draw up to 22amps. The pin AM3 socket. Distributed Computing – General.
You should not need any drivers at this point as Windows Vista and later have built in drivers that will work until you install your chipset drivers. Connectivity comes in the form of eight USB ports on the rear panel, with another four available through the use of a motherboard header.
Gigabyte GA-MA790FXT-UD5P – motherboard – ATX – Socket AM3 – AMD 790FX
Note that passwords are case-sensitive. In order to be able to post messages on the Overclock.
Do you know how many issues I have read on here just this week that were caused by bad installation media. My concern for your setup is that the memory crash may have caused bad data to be written to the disks Using cheap ram a few years ago, a faulty stick would install windows fine, but while using ga-ma790fxt-hd5p, would write bad data back to the hdd’s at shutdown causing it to fail ga-ma70fxt-ud5p boot beyond a blue screen.
First, in the bios you’ll have to set your drives up. For the best viewing experience please update your browser to Google Chrome. When I replaced the ram I had to reinstall as many base system files were messed up.
Redo windows to the new raid and see how it works. If you do not want to register, fill this field only and the name will be used as user name for your post. For those who are building high-end Phenom II systems, this likely won’t be a large loss since discrete graphics will always outperform IGPs. Of course, the paper specs are only half the story, and the real question that’s on everyone’s mind is how the new Phenom Radi processors will overclock on this motherboard.
And make sure you configured raid 0 right on the board in bios. June 02, The coolest thing about it is that it’s specially protected by a clear security cap, so you can lift it off and pretend you’re nuking the eastern sea board instead of nuking overly ambitious system settings.
Look for the Vista 64 raid drivers for your board and install them when you are prompted. I tried the ‘load driver’ option but it just comes up saying its an unsigned driver and cant continue!
I intend to use Gigabyte Smart Backup, never ga-ma790fx-tud5p it before, is it good, can I restore all if my system crash, will it restore just the data, system files or both.
Low Tide 12 items.
Gigabyte GA-MAFXT-UD5P AMD FX Socket AM3 Motherboard Review –
Thanks for your time. Since AMD long ago moved the memory controller from the motherboard’s ga-mw790fxt-ud5p and onto its processors, the FX chipset that was used with DDR2 motherboards is also used in DDR3 motherboards, with a minimum amount of fuss. Operating System Windows X. Well I hope someone could help me to setup my system so I could boot from my Raid 0, I wish I don’t have to reinstall all again, now the system boots form c: Also take into effect all the complaints about that ram you are using and its a headache waiting to happen.